EASA Part 66/147 compliant Module 7; Maintenance Practices for the A through B1 and B2 aircraft maintenance certification. This book teaches to the required levels and to an extent typical of an EASA certified 2 year Part 66/147 aircraft engineering program.
eBook File Description:
TABLE OF CONTENTS:
Safe working practices including around electricity, gases, oils, and chemicals. Action in case of fire and knowledge of extinguishing agents.
7.2 Workshop Practices
Care and control of tools and materials; allowances and tolerances; standards of workmanship. Calibration of tools and equipment.
Common hand tools and power tools; precision measuring tools; lubrication equipment and methods; functuion and use of electrical test equipment.
7.4 Avionic Test Equipment
Operation, function, and use of avionic general test equipment.
7.5 Engineering Drawings and Standards
Drawing types, symbols, dimensions, tolerances, and projections; title block information; microfilm and computerized presentations. ATA Specification 100. ISO, AN, MS, NAS, and MIL standards. Wiring and schematic diagrams.
7.6 Fits and Clearances
drill sizes, classes of fits; schedules of fits and clearances for aircraft and engines; limits of bow, twist, and wear; standard methods for checking shafts, bearings, and other parts.
7.7 Electrical Wiring Interconnection System (EWIS)
Continuity, insulation, and bonding techniques and testing. Use of hand and hydraulic crimp tools. Testing crimp joints. Connector pin removal and insertion. Co-axial cables, testing and installation. Identification of wire types, inspection criteria, and damage tolerance. Wire protection techniques; cable looming and support; cable clamps, protective sleeving including heat shrink and shielding.
Riveted joints, spacing and pitch. Tools for riveting and dimpling. Inspection of riveted joints.
7.9 Pipes and Hoses
Bending, belling, and flaring aircraft pipes. Inspection and testing of pipes and hoses. Installation and clamping of pipes.
Inspection and testing of springs.
Testing, cleaning and inspection of bearings. Lubrication requirements. Defects of bearings and their causes.
Inspection of gears and backlash. Inspection of belts, pulleys, chains, and sprockets. Inspection of screw jacks, lever devices, push-pull rod systems.
7.13 Control Cables
Swaging of end fittings. Inspection and testing of control cables. Bowden cables, aircraft flexible control systems.
7.14 Material Handling
Sheet Metal: bend allowance, metal working, inspection. Composites: bonding environmental conditions, inspection.
7.15 Welding, Brazing, Soldering, and Bonding
Soldering methods and inspection. Welding and brazing methods, and inspection. Bonding methods and inspection.
7.16 Aircraft Weight and Balance
Center of gravity/balance limits and calculation and use of relevant documents. Preparation and weighing of aircraft.
7.17 Aircraft Handling and Storage
Aircraft taxiing, towing, and associated precautions. Aircraft storage methods. Refueling and defueling procedures. De-icing and anti-icing procedures. Electrical, hydraulic, and pneumatic ground supplies. Effects of environmental conditions on handling and operation.
7.18 Disassembly, Inspection, Repair and Assembly Techniques
A) Defects and visual inspection; corrosion removal, assessment, and reprotection. B) general repair methods; aging, fatigue, and corrosion control programs. C)Non-destructive inspection including penetrant, radiographic, eddy current, ultrasonic, and boroscope methods. D) Disassembly and reassembly techniques. E) Troubleshooting techniques.
7.19 Abnormal Events
Inspection following lightning strikes and HIRF penetration. Inspections following heavy landings and turbulence.
7.20 Maintenance Procedures
Maintenance planning; modification procedures; stores procedures; certification/release procedures; interface with aircraft operations; inspection and quality control assurance; control of life limited procedures.
- ...from the 'tools & hardware' Category
- > Maintenance Practices for Aviation Maintenance
- > Taps and Dies
- > How to Crimp Battery Connectors
- > How to Cast Small Metal & Rubber Parts
- > Use and Abuse of Twist Drills
- > Aircraft Mechanic's Specification Handbook
- > Materials and Hardware for Aviation Maintenance
- > Care and Handling of Borescope Equipment
- > Tapered & Straight Reamers
- > RV Rudder Workshop
- ...from the 'EASA Part 147' Category
- > About EASA
- > Propellers and Propeller Systems
- > Mathematics for Aviation Maintenance
- > Physics for Aviation Maintenance
- > EASA Legislation for Aviation Maintenance
- > Gas Turbine Engines for Aviation Maintenance
- > Electrical Fundamentals for Aircraft Maintenance
- > Maintenance Practices for Aviation Maintenance
- > Electronic Fundamentals for Aircraft Maintenance
- > Basic Aerodynamics For Aviation Maintenance
- Pilot Ratings
- flight instructor
- ATPL - easa/jaa
- CFI & FBO resources
- Flying Skills
- regulatory - flight
- VFR skills
- IFR & navigation
- professional skills
- communication / English
- sport flying
- aircraft & systems
- operating handbooks
- avionics training
- flight safety
- A&P Training
- A&P text books
- A&P test aides
- A&P training kits
- professional resources
- instructor resources
- EASA Part 147